![]() |
Re: Anyone goin to RF this saturday?
i want to take mine out but still tuning. saw jakes turbo the other day, while looking for coolant lines, things friggin massive. thanks for the lines jake
|
Re: Anyone goin to RF this saturday?
Here are more pictures... http://www.vasso.net/jake/
The car is AWD... Fully built motor and everything is supported. Its running good but having a little problem with the tune so I might not race tomorrow but I will still go to the track. Also, the turbo is not a 42r. It is similar but not entirely the same. It has a smaller exhaust wheel and close to the same size compressor wheel in one of the models, yet it still uses the same compressor housing. It has a P-Trim exhaust wheel with a .68A/R turbine housing and a 72mm compressor wheel. I just am completely amazed that it fit so well. The turbo is so massive yet it clears everything. I had to make 2 modifications, grind a little off the bracing on the DNP manifold and cut a little out of the cross member for the lower IC piping to attach to the turbo. Other than that it fits perfect. Oh and dent the water pipe slightly. Not very much at all. Spools good and pulls very hard. I'm impressed with it. |
Re: Anyone goin to RF this saturday?
So did anyone go? How did everyone do?
|
Re: Anyone goin to RF this saturday?
Quote:
|
Re: Anyone goin to RF this saturday?
Good Gosh! that turbo is huge! Are you sure you have the right one. That looks like something off a catapiller earthmover. Probably start spooling at about 7000 rpms -eh? :D
What's with all the metal shavings? Hope none of that got in the inlet. |
Re: Anyone goin to RF this saturday?
I was there for a few minutes but I took my g/f's car seeing mine was still having some problems. I just went there to drop off some parts and saw some runs then left cause I had other stuff to do. Didnt look that busy at all. Seemed like there were very few cars there, but I also didnt show up until 1pm.
I see 1lb of boost on that turbo at 5500rpms. Lag is over rated. The metal shavings were from me having to grind on the support bracket that is attached to the DNP manifold. No shavings went into the turbo. Its nice, I like it, just wish I could get this damn thing running right. |
Re: Anyone goin to RF this saturday?
Quote:
12.61 @ 108.9mph. Clutch is completely gone now... oh well. I will have a Tilton twin disc ordered. |
Re: Anyone goin to RF this saturday?
Oh darn, time to upgrade. Sometimes it is nice to be forced into upgrading:D
|
Re: Anyone goin to RF this saturday?
Nothing wrong with 12.61, IMO- Anything in the 12's is a respectable time. I'd rather have a reliable 12 second car(which I do), than a 10 sec. car that's on jack stands most of the time.
|
Re: Anyone goin to RF this saturday?
How much boost were you running Cher? The trap and ET seems low for your mods. Ryans EVO ran 12.6@110 with less mods than yours has (cams/AEM). Or was the clutch holding you back from really launching the fuck out of it?
|
Re: Anyone goin to RF this saturday?
Quote:
Who knows what was going on. I was expecting a better MPH too. I was running 20-21 psi on 92 octane. The clutch is just completely toast as when it sees 1 psi of boost, it slips like mad. :-S |
Re: Anyone goin to RF this saturday?
I would guess with your mods and a good tune it should be trapping at about 113 or so. Its probably running a bit rich or you have the knock table setup pretty aggressive. Either way a 12 is a 12.
|
Re: Anyone goin to RF this saturday?
Were there many dsms there? A friend of mine went in his red 98 gsx and ran 13 flat. He said he didn't see many dsms there. He said he might have been the only t/e/l there. Either that or he wasn't really paying attention.
|
Re: Anyone goin to RF this saturday?
I didn't see 1 turbo dsm run all day. There were 4 or so non turbo's running around.
Anyone notice the "my car doesn't have a hood" craze? |
Re: Anyone goin to RF this saturday?
Quote:
|
| All times are GMT -5. The time now is 06:54 PM. |
Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.