Re: joel's build
 

Nice you busy? Wanna come tear a 1G apart?

Re: joel's build
 

Just bought a set of BC272 cams on tuners for $275 shipped.

The only question I have is I was thinking about just using my stock springs and retainers. Do you think that would be a bad choice to make?

Re: joel's build
 

Bc272 can run with your stock head with out a prob. However, it's recommended that you upgrade the springs and retainers when putting in cams.

Re: joel's build
 

How high do you plan to rev? How many miles are on your stock springs/retainers?

The cams will be increasing valve liftand duration over stock, so you will be asking more from your valvetrain which increases your risk of failure. The risk increases more if you plan to rev higher, or your stock components are tired. Whether or not that risk is increased by enough to make it worth upgrading is your call.

If it were me, if the head was coming off I'd get new springs put in. If not, I'd run the stock stuff and just not rev it to the moon, and replace the springs next time the head comes off.

Re: joel's build
 

The head is going to come off so I think I am going to be smart and do them right away.

The stock springs have 133000 miles and I rev to 7500 rpm.

Re: joel's build
 

Good call.

You should be able to find a cheap spring upgrade if you are on a budget from crower or similar. Those cams don't appear to be that aggressive that you'd have to fork out for a dual spring or beehive setup. Just a cheap single spring upgrade should be plenty for those cams, and allow you to rev to 8k without worrying much about valve float / jumping. I ran crowers on my 1g with HKS 272's up to 8000rpm.

Re: joel's build
 

Cool thank you for the info.

Re: joel's build
 

Well the car is in the garage and am starting to pull everything apart.

If anyone is board and wants to lend a hand. I'm located off of 22 in linwood. Give me a call

763-447-8990

Re: joel's build
 

Thanks to cornfed2.4 the engine and trans are out of the car, trans is separated and readt to tear into it.

http://i85.photobucket.com/albums/k4...ps23ea018a.jpg

I am going to spend tomorrow cleaning the engine bay. Then I have to disassemble the head and pull it off.

I am also going to read up on how to do valve springs. If anyone that knows how to do them can maybe help out that would be amazing.

Re: joel's build
 

Nice work! Once the head is off valve springs aren't too hard but you're going to have to get your hands on a valve spring compressor. Personally if the head is off and you can swing it I would bring it to a shop and have them go through it. A stock valve job at the place that did my cylinder Head is only like $300.

Re: joel's build
 

I don't think I am going to do anything like that just put in the new springs and cams and call the good.

Re: joel's build
 

cleaned up the engine bay some today. Deleted all the evap garbage, and got the engine on its stand. One downer I am not sure what is wrong with the #4 cylinder. 1, 2, and 3 where all dry but in the #4 seemed to have some wet oil in it. Not sure if it is head gasket leaking oil into the cylinder, rings, or valve seals.

http://i85.photobucket.com/albums/k4...ps8ad33fa7.jpg


Also my evo3 16g was SHOT there was more in out play then I have ever felt on a turbo. I don't know how it even made boost. The up down play was perfect.

Re: joel's build
 

Little bit of of progress tonight on the head. Got all the exhaust valve springs and valve stem seals replaced. Tomorrow is all the intake valves, and cams. after that the head is ready to go back on.

Re: joel's build
 

Got a lot of progress today.

Finished installing my new Brian Crower valve springs, new valve seals, and Brian Crower 272 cams.

http://i85.photobucket.com/albums/k4...ps3c46c65e.jpg

Got my $8 ebay shift cable bushings installed.

http://i85.photobucket.com/albums/k4...ps5ff91e2b.jpg

Also cleaned all the head gasket mating surfaces, and installed my H11 head studs.

http://i85.photobucket.com/albums/k4...ps05793764.jpg

The only thing I have a question about is this stuff what I want to use when torquing down the head nuts on the studs.

http://i85.photobucket.com/albums/k4...ps5c150601.jpg

Re: joel's build
 

No don't use that stuff. I grabbed a tub of that and Shawn (4seasons69). Said it wasn't the same stuff that you need.

Re: joel's build
 

k thanks.

Re: joel's build
 

You can get by with engine oil if you need to but I would use the arp moly lube. I might still have some. I'll check and see

Re: joel's build
 

I am in need of some help. I don't have the timing belt tension tool need to set the tension on my belt. If anyone is interested in lending a hand that would be amazing.

Re: joel's build
 

You really don't need one.

Re: joel's build
 

I have read that. And how it all should work I just can't compress the pin in the adjuster to put the allen in it. And its my first time timing my belt and would like a 2nd pair of eyes to say its ok.

Re: joel's build
 

gotta put the tensioner in a vice and slowly squeeze it in is much easier if you do it slow

Re: joel's build
 

Hahaha thats the other issue. No table vice.

Re: joel's build
 

lol that could be an issue. Um can also use a big channel locks?? done that before

Re: joel's build
 

Actually, you HAVE to do it slow. If you go too fast, you'll rupture a seal.

What city are you in, Joel?

I've used a car and jack before... Not the best way but it gets the job done.

Re: joel's build
 

In Linwood by wyoming.

Re: joel's build
 

Thanks for the floor jack idea... lol

http://i85.photobucket.com/albums/k4...ps256ab76e.jpg

Re: joel's build
 

Timing belt is installed. only thing I am worried about is the tension. Should be good I am always over worried.

Re: joel's build
 

Did you do the drill bit check to see if the tension is right?

Re: joel's build
 

I did using allen wrenches.

Re: joel's build
 

Everything is all assembled and ready to go back into the engine bay. Going to try and get most of it done tomorrow. And have it running and driving sometime this weekend.

http://i85.photobucket.com/albums/k4...ps09944adf.jpg

Re: joel's build
 

Looks good! Hope to see it pick on some more v8 cars this summer ;)

Re: joel's build
 

Good job!

Re: joel's build
 

Big update tonight.
Installed the clutch and trans, and dropped it in the bay
Got all the wiring and vacuum lines hooked up. Starter and axles installed. It is getting close to being ready to start.

To do list.
Transfer case
Down pipe
Oil feed and return lines
Radiator
Intercooler
And fill all the fluids.
Thanks Nick for all the help.

http://i85.photobucket.com/albums/k4...ps04f940dc.jpg

Re: joel's build
 

Whats the deal with the transmission?

Re: joel's build
 

The trans that I am going to have you look at is the one I broke last year. The one in the pic is a tre stage 3
I got all caught up in finishing my car I didn't get a chance to pull those calipers for you. I hope to have them pulled mon.

Re: joel's build
 

So much for going right to sleep! Did get alot done though.

Re: joel's build
 

Laying in bed I thing my dog is going to have a heart attack because of the lighting.

Re: joel's build
 

Nice work, can't wait to see it done.

Re: joel's build
 

I need to find me some of that motivation.

Re: joel's build
 

Well it is finished. Everything went to plan. started right up, and no leaks. this was the first start up started running rough at the beginning, and cleared up after a few seconds.

The excitement I get after tearing it all the way down to the short block and putting it back together and it working perfect is amazing.

Big thanks for the help Cornfed2.4

https://www.facebook.com/photo.php?v...30897824253440