01-23-2009
|
#81
|
formerly ecoli
Join Date: Oct 2003
Location: On the dyno
Posts: 4,892
|
Re: Beater 2g
I got to drive it, it's damn loud at part throttle.
|
|
|
01-23-2009
|
#82
|
is Nashty
Join Date: Oct 2007
Location: Stillwater
Drives: Cyborg from Japan
Posts: 2,080
|
Re: Beater 2g
Why? "Droney" exhaust?
__________________
-1990 Mitsubishi Cyborg 4WD-
|
|
|
01-23-2009
|
#83
|
formerly ecoli
Join Date: Oct 2003
Location: On the dyno
Posts: 4,892
|
Re: Beater 2g
No exhaust.
|
|
|
01-23-2009
|
#84
|
is Nashty
Join Date: Oct 2007
Location: Stillwater
Drives: Cyborg from Japan
Posts: 2,080
|
Re: Beater 2g
Oh.. well I suppose that would explain why. haha
__________________
-1990 Mitsubishi Cyborg 4WD-
|
|
|
01-23-2009
|
#85
|
Join Date: Aug 2005
Posts: 79
|
Re: Beater 2g
I saw you a few times last fall at st. thomas driving this around
__________________
![](image.php?s=40c61b092f779ffbce0341162f6dbf18&u=931&type=sigpic&dateline=1232579469)
91 gvr4 dd, 04 open class sti rally car, 97 k2500 toy hauler
2010 events: sno*drift, 100AW, STPR, OFR, LSPR, NT1-3
|
|
|
01-23-2009
|
#86
|
N17r0U$ br4D
|
Re: Beater 2g
Quote:
Originally Posted by importcarkid
Brad I want a Ride when you get up and going again!
|
No prob bob.
Quote:
Originally Posted by ecoli
I got to drive it, it's damn loud at part throttle.
|
You loved it, haha. Some days I wish I had an exhaust on the car, but I always find different ways to spend the money.
Quote:
Originally Posted by carlvr4
I saw you a few times last fall at st. thomas driving this around
|
I saw the vr4 around a couple times too, looked really clean! You still going to St. Thomas?
Over the last week I picked up a new stainless clutch line, an adapter to get rid of the banjo bolt on the fuel filter so I can run -6 an from the filter to the rail (figure every little bit helps), and a new slave cyl/throw out bearing/clutch fork from Nick over at Brookdale. Probably get a new fuel filter before the trans goes back in as well.
Hopefully once I'm done with the J-term, I will have some time on my hands to get the back on the road and break in the trans in. It'll be nice to drive a kinda fast car, even if I can't beat on it.
__________________
My rice rocket best times
Pump Gas: 8.85 @ 152.3 in 2016
Race Gas: 8.982 @ 152.16 in 2014
|
|
|
01-23-2009
|
#87
|
is Nashty
Join Date: Oct 2007
Location: Stillwater
Drives: Cyborg from Japan
Posts: 2,080
|
Re: Beater 2g
So you have been driving the car with no exhaust the whole time? I didn't notice you didnt have an exhaust when I stopped over that night..
Good choice on the banjo bolt replacment. My Walbro 255 went from a high pitch hum to a very low drone from just replacing that fitting.
__________________
-1990 Mitsubishi Cyborg 4WD-
|
|
|
01-23-2009
|
#88
|
N17r0U$ br4D
|
Re: Beater 2g
Quote:
Originally Posted by 4g63tcrazy
So you have been driving the car with no exhaust the whole time? I didn't notice you didnt have an exhaust when I stopped over that night..
Good choice on the banjo bolt replacment. My Walbro 255 went from a high pitch hum to a very low drone from just replacing that fitting.
|
Yep I've had no exhaust on it the whole time. I almost want to throw a stock muffler not connected to anything in the back and pretend like I just have a huge exhaust leak. haha
Yea hopefully with summer blend, the banjo bolt replacement, and the boost a pump I can make a little more power.
__________________
My rice rocket best times
Pump Gas: 8.85 @ 152.3 in 2016
Race Gas: 8.982 @ 152.16 in 2014
|
|
|
01-23-2009
|
#89
|
is Nashty
Join Date: Oct 2007
Location: Stillwater
Drives: Cyborg from Japan
Posts: 2,080
|
Re: Beater 2g
Good luck. I remember when I was just running a dp it was loud as hell and I had to drive to Rockfalls like that.. But the exhaust was cut off right under me so I suppose it was worse. I wanna hear this thing now! haha. If you ever drive past 39th street on a weekend (When im usually home) make sure you give it a good pull!
__________________
-1990 Mitsubishi Cyborg 4WD-
|
|
|
01-23-2009
|
#90
|
Kevin
Join Date: Jan 2004
Location: Shoreview
Posts: 3,356
|
Re: Beater 2g
I really like your car.
__________________
Misses the Mitsu Community
Currently on Corvette #4
|
|
|
02-15-2009
|
#91
|
N17r0U$ br4D
|
Re: Beater 2g
Pulled the engine out last night while the trans was still off to make it easier to fix the couple small leaks I had. While its out I kind of thought about possibly building the engine, getting some suspension, better fuel pump setup. I kind of have ADD when thinking of things to buy so I keep going back and forth on what to get
I also don't have a ton of money to play with, so I'd like to keep mods to 2k or below to get ready for summer.
That being known what would you guys recommend? I haven't done much reading on engine building so I feel like a huge n00b so any suggestions with pistions, compression, rods, etc would be very much appreciated!
Kind of want to put the boost a pump I have sitting around in, small shot of nitrous and "Let'R Buck" with the stock 6 bolt. The only problem with this method is I don't seem to have a lot of time on my hands lately to work on the car so once it blew I probably wouldn't have any money or time to work on the poor little guy.
So any suggestions would be great!
Last edited by C3L1CA; 03-10-2009 at 01:21 PM..
|
|
|
02-15-2009
|
#92
|
Join Date: Mar 2005
Location: Blaine, MN
Drives: '91 Automagic
Posts: 13,908
|
Re: Beater 2g
Stock bottom end should hold up just fine.
Will that tranny hold a shot?
I plan on doing a single maybe with a KB BAP if needed, my goal is the same as yours minus the power/trap thing
|
|
|
02-15-2009
|
#93
|
N17r0U$ br4D
|
Re: Beater 2g
Quote:
Originally Posted by turbotalon1g
Stock bottom end should hold up just fine.
Will that tranny hold a shot?
I plan on doing a single maybe with a KB BAP if needed, my goal is the same as yours minus the power/trap thing
|
Yea I'm starting to think my power level isn't crazy enough to see a built motor. Maybe someday once I get a real job and out of school.
I just picked up a tre stage 3 this past winter, so I'd hope it can hold the little power I would make. I didn't plan on spraying anything too crazy, first thoughts were to spool quicker but if the fuel is there I'd like to try maybe a 50 shot all the way to redline. I guess only time on the dyno with the BAP will see what ends up happening. I don't even know how much the BAP will even help, haven't seen any body posting any before and after numbers.
What are your goals? You going for times?
|
|
|
02-17-2009
|
#94
|
Join Date: Mar 2005
Location: Blaine, MN
Drives: '91 Automagic
Posts: 13,908
|
Re: Beater 2g
I am with you on the job thing, so hopefully the next few months will prove good for me.
My goal is to be a bit more laggy than the 16g and be able to pull to 7000-7500rpm since i had to shift at 6600rpm last year.
I don't care how fast this car is, but if i can beat 600s easily it will, be a plus.
Z is what i want to be the fast/fun car, dsm for dd.
OH, pick up a ford gt pump, its a 310 and with a BAP could be good. I hope i am good with a single pump. I don't plan on making enough to need more.
Whats in the stg. 3?
|
|
|
03-10-2009
|
#95
|
N17r0U$ br4D
|
Re: Beater 2g
w00t for getting my brake lines today for the abs delete, hopefully I find motivation after this week to work on the hunk of junk.
Also had Danny up at DB weld on some -10 bungs onto my valve cover.
Mounted the bottle and the box should be mounted by the end of the week. Don't mind the pitcher holding the box up.
I'm pretty happy with how I mounted the solenoids. I wanted to hide them but didn't really know where to put them. I ended up putting them in my battery box I made which led to the battery relocation. I'm going to make a cover to put over the top of it so it'll just look like a battery box.
The ricer in me also wanted to get a new boost gauge.
![](http://i6.photobucket.com/albums/y202/C3L1CA/IMG_0108.jpg)
__________________
My rice rocket best times
Pump Gas: 8.85 @ 152.3 in 2016
Race Gas: 8.982 @ 152.16 in 2014
|
|
|
03-10-2009
|
#96
|
Join Date: Mar 2006
Location: FargO
Drives: the girls crazy
Posts: 3,012
|
Re: Beater 2g
wow brad. That thing is gunna rip!
__________________
pics or gtfo
|
|
|
03-10-2009
|
#97
|
Reynolds number user
Join Date: Oct 2003
Location: grove/tempe
Posts: 3,553
|
Re: Beater 2g
totally gonna make more than 93.2 hp
__________________
07 Ducati Monster S4R
00 honda elite 50 (64 mph braH!)
05 malaguti F15
04 E55 AMG
|
|
|
03-10-2009
|
#98
|
flips McGee
|
Re: Beater 2g
WOOT! Bring this beast to the dyno day, should be fun to check it out!
|
|
|
03-10-2009
|
#99
|
N17r0U$ br4D
|
Re: Beater 2g
Quote:
Originally Posted by Mr.98GSX
wow brad. That thing is gunna rip!
|
I don't know about all that, but it should be pretty fun as long as it holds together.
Quote:
Originally Posted by Super Bleeder!!
totally gonna make more than 93.2 hp
|
haha I hope so, if not I heard I stickers add some mighty fine hp if placed strategically.
Quote:
Originally Posted by scheides
WOOT! Bring this beast to the dyno day, should be fun to check it out!
|
I'll be there for sure, car should be too even though its not much to look at.
__________________
My rice rocket best times
Pump Gas: 8.85 @ 152.3 in 2016
Race Gas: 8.982 @ 152.16 in 2014
|
|
|
03-10-2009
|
#100
|
Join Date: Nov 2003
Location: Duluth
Drives: a pos
Posts: 722
|
Re: Beater 2g
What size bottle is that?
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
|