this looks to good to be true, has it been proven?

[Tachyon]

Originally Posted by M1L3S

so for a 2.3 hx40 build , wanting 500ish do you think it would be a benefit or a restriction?


ive read that it out flows a 1g , but not by much.

seeing how my engine is already a 2.3 I figured the cyclone would give even more grunt in the low end before boost steps in.

With an HX-40 I would use a SMIM over the Cyclone because the turbo can supply sufficient airflow that it makes sense to make the engine more efficient in the upper RPM range.

[blackrosenova400]

Originally Posted by Tachyon

With an HX-40 I would use a SMIM over the Cyclone because the turbo can supply sufficient airflow that it makes sense to make the engine more efficient in the upper RPM range.

I agree, it would not be a good choice for comparing it to a smim for 1/4 mile drag racing and overall power. But for a fun street car, and maybe the 1/8th mile, I like it!

[blackrosenova400]

FYI: It was a pain to clear the A/C compressor, and it was a pain relocating the coil pack and setting up the wastegate actuator.

You can kind of see the wastegate actuator under the spark plug wires.

[Tachyon]

Damn, Chad... that looks awesome!

Are you going to be at the spring dyno with it?

I think a friendly peak TQ contest would be in order

[blackrosenova400]

Originally Posted by Tachyon

Damn, Chad... that looks awesome!

Are you going to be at the spring dyno with it?

I think a friendly peak TQ contest would be in order

Im currently upgrading my 20g to a billet 20g extended tip, then replacing my 7cm housing with a fp 8cm housing. Then some other minor things I hope to get done by this spring, and make it to the dyno day.

[Tachyon]

Originally Posted by blackrosenova400

Im currently upgrading my 20g to a billet 20g extended tip, then replacing my 7cm housing with a fp 8cm housing. Then some other minor things I hope to get done by this spring, and make it to the dyno day.

Which billet wheel did you go with? The thread on Tooners made me want to poke my eyes out...

[blackrosenova400]

Originally Posted by Tachyon

Which billet wheel did you go with? The thread on Tooners made me want to poke my eyes out...

Kamak 6+6

[M1L3S]

Originally Posted by blackrosenova400

FYI: It was a pain to clear the A/C compressor, and it was a pain relocating the coil pack and setting up the wastegate actuator.

You can kind of see the wastegate actuator under the spark plug wires.

was it hard to set everything up and make it work together ? I have no ac etc.( I mean tune wise )

1g throttle body bolt right up ?

dis the intake make a well worth it difference?

[blackrosenova400]

Originally Posted by M1L3S

was it hard to set everything up and make it work together ? I have no ac etc.( I mean tune wise ) dis the intake make a well worth it difference?

1g throttle body bolt right up ?

1g throttle body bolts right up. I run speed density with an evo 8 ecu. If your running speed density it will have to be tuned. If your running a maf sensor it should be able to pick up the extra airflow and relay to the ecu alot better.

Yes I do see a nice extra airflow chunk down low




.

[M1L3S]

Originally Posted by blackrosenova400

1g throttle body bolt right up ?

1g throttle body bolts right up. I run speed density with an evo 8 ecu. If your running speed density it will have to be tuned. If your running a maf sensor it should be able to pick up the extra airflow and relay to the ecu alot better.

Yes I do see a nice extra airflow chunk down low




.

just mean you dont need any additional parts besides the mani? where did you find your gaskets ?

[blackrosenova400]

I didnt use gaskets. I cleaned the intake mating flanges thoroughly and used anerobic sealant instead of gaskets.

[M1L3S]

Originally Posted by blackrosenova400

I agree, it would not be a good choice for comparing it to a smim for 1/4 mile drag racing and overall power. But for a fun street car, and maybe the 1/8th mile, I like it!

manily a street set up, I have a buddy with a integra that wants a go, and another buddy with a vett.